Faux Fired Up

It all started with a text from my mom. She had found a mantel at her local Restore in Tennessee for around $66. The text was accompanied by this picture.

After asking some questions and thinking it over, I texted her to pick it up. This began a three week journey for this fireplace accoutrement, from Restore floor to our dining room.

I had wanted a mantel for our dining room since we had moved in. It didn't need to work, it just needed to be a traditional representation of what a dining room means. It tends to be a place where people gather around a fire/table and be together. I also liked how it gave a more official dining room feel to a room that was originally the living room. It had always needed a little help not feeling like an after thought of an area.

On Pinterest, of course, I had fallen in love with this image from the blog Bless'er House.

http://www.blesserhouse.com/2014/07/diy-faux-fireplace-entertainment-center_28.html

It was visually demanding, yet very airy in the room. I loved the stone surround, but especially the wood cuts in the center. It was a definite inspiration for what our new acquisition was to become.

Since Mom and Dad weren't going to be in town for a while, they ended up storing the mantel for us. I slowly started receiving text updates.

Would you like me to strip the paint off?

I might be able to get a coat of paint on it before we bring it to your place.

Suddenly, the mantel was being worked on and I was getting pictures. I am pretty sure she was having as much fun working on it as I would have.

Here she is using a heat gun to remove the old paint. The original paint job was chipping and needed to be completely redone. She tried stripper first, but the heat gun apparently worked best.

She was then able to scrap off the old paint with a metal putty knife. I wouldn't recommend a plastic one because it might melt.

When she really got going, she had taken off all of the original paint. In all, she said it took 16 hours! Never say I don't owe my mom!

She followed up with stainable wood putty, some sanding, and a coat of white paint. The next time I saw it was when their truck pulled into my driveway. It looked great already! There was still much to do to install it, though.

We brought it inside and set it where we wanted it. After giving it side glances overnight, Dad brought up the idea of adding a hearth to the bottom. This would both lift the mantel off the ground and away from the moulding, but also help complete framing around the interior portion (where the wood or fire would normally go).

Dad and Scott started with a simple frame with 2x4s.

Then they skinned it in some nicer plywood. We had purchased a 4x8 ft piece at Home Depot and ended up needing most of it for the entire project. Strips of it were cut to size to skin the hearth. They were then attached with wood glue and nails from our nail gun.

Dad scroll cut the sides from a template Mom drew to fit it against the moulding and we brought it in to take a look.

We thought it looked pretty good, so Mom and I put a couple of coats of white paint on it while the boys started work on the actual mantel itself.

First, they added about a 6 inch surround to the interior of the mantel. This would keep the wood pieces from being visually overwhelming and also help it feel more realistic. They did this using the same piece of plywood from earlier.

Then, they attached small pieces of 1x2 around the opening as spacers to set back the interior piece a little. This added some nice dimension to the over all look.

The interior was yet another piece of the plywood. I had painting it black before they installed it so it would be easier to work on later. When the structure was completed it looked like this.

Notice the stair stepping of the layers.

At this point, the mantel now weighed twice as much, but of course, we weren't done. We carried it inside and checked it in its place. We were chugging along nicely.

Spiffy

We brought it back outside and began working on the interior and finishing stages of the process. I painted the inside of the opening black to match the background. Then we were off to the woodpile.

Dad used this chainsaw and cut through a bunch of our branches that we have around for the fire pit. He eyeballed the size and was impressively accurate. For the smaller branches, he was able to set up a stop on our miter saw and get the same size every time.

While he cut, I began placing the pieces in the interior area of the mantel. After about 30 minutes, we had a very pleasing arrangement.

To attach all of the wood pieces, we had a very odd system (that worked really well!). Dad laid under the saw horses and I used a drill to drill a pilot hole from the top under each piece.

Then Mom came in and glued each piece down while Dad screwed in each log from the underneath so it didn't show. It looked a little something like this.

After about 20 minutes and my father being thoroughly covered in sawdust and glue, we were able to set the fireplace on end.

From behind, you can see alllllll the screws.

Of course, now that it was about 1,000 lbs, it was time to move it inside.

The hearth was first attached with L-brackets and anchors to the wall.

Then the mantel was attached using two screws with anchors as well.

It looked great! There was just one problem...

It was in the wrong place.

When this all began, I had measured the far wall to see if the two bookcases and the fireplace could all fit together. It seemed like the fireplace being centered would give that traditional vibe I was going for.

Unfortunately, numbers make fools of us all. I had measured and written down the wrong number. After living with the mantel on the side wall for a couple of days, my curiosity got the best of me and I remeasured. Sure enough, it would totally fit (with extra space) on the far wall.

I very sweetly told Scott that I had royally screwed up and he agreed to help me move it. The move, I must say, really helped cement this as one of my favorite house projects so far.

Much better!

What do you think, is it worth having an architectural piece if it doesn't work, or are fireplaces meant to be used, not just seen? I have to say, even though this guy will never heat our home, I'm already a big fan of how grand it makes the space feel. I can't wait to spook it up for Halloween and hang our stocking on it at Christmas!

PS-See the retro TV on the right? My Found TV Bourbon Bar Blog Post coming soon!

Time to Vent

There is something to be said for the little things. The things that get looked over because they aren't that important. Today, we are giving a little love to one of those little things. I am referring, of course, to the lowly vent cover.

While I was measuring a wall in our dining room for a different project, I happened to get an eye full of what could be described as a "rusty gate into a windy, spidery hellscape that lives under our home".

First of all, it was gray. The wooden floors have never been gray, so it made no sense that the floor vents continue to be. I decided they were in need of a quick spray down.

I had always seen Pinterest show how you could spray paint vent covers, but thought it was odd that they would spray vent covers for honey colored wood floors in oil rubbed bronze. Doesn't it seem like you'd like them to disappear rather than stick out more?

So I took matters into my own hands. I removed the vents and cleaned them. Off to the garage we went.

I did the flaps of the adjustable vent first. This just kept the very top of the vent from getting ruined when it was flipped over to paint the other side.

I started with primer, which I happened to have around.

Then gave them a nice coat of the same copper spray paint that I had purchased for my side table.

Once that had time to dry, I just flipped over the one with vents and did the same process over again.

I didn't worry too much about the original gray paint coming off. Even though they were getting a little upgrade, they were still just vents. No need to strip them completely and start from scratch.

When they were finished, they really looked great. The copper blends with the floors beautifully, and the metallic gives the space just a hint of bling.

And that was it! I have also done the ones in our guest room, and am continuing around the house till they are all "copper plated". If you do have dark wood floors, though, I recommend checking out my friend Beth's blog Over on Dover about how her oil rubbed bronze covers got a face lift.

PS-There will be more information on two other big projects we just completed in the days to come. Stay tuned!